BEGINNER'S PLUMBING: WHAT YOU NEED FOR BATHTUB INSTALLATION

Beginner's Plumbing: What You Need for Bathtub Installation

Beginner's Plumbing: What You Need for Bathtub Installation

Blog Article

Click For More Information

What're your insights and beliefs on Installing A Bathtub?


How to Install a Bathtub Yourself
Setting up a tub isn't exactly rocket science, but it does require strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the project can relocate speedily; if you need to open up a wall surface to eliminate the old bathtub as well as position the brand-new tub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have qualified on your own for the task and are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This post will certainly aid you install a brand-new bathtub in your restroom if you have actually already purchased a brand-new bathtub and also do not need to transform the plan of your previous water pipes.
Your devices as well as material list should make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Setup


    First of all, the sustaining structure supplied with the bath should be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to avoid stress on the tub.
    Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the supplied washers.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final position.

    Removing Old Taps


    If you require to change old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome as a result of the restricted access that is often the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipes have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
    Before going on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Mounting the Tub


    Utilizing the two wooden boards under its feet, put the bath tub in the needed setting. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the tub up until the spirit level checks out level.
    To set up taps, fit the bottom of the outermost adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
    Activate the water and examine all joints and new pipework for leakages as well as tighten them if essential. Load the bathtub as well as likewise check the overflow outlet and the regular electrical outlet for leakages.
    Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub should wait up until the bathtub has actually been made use of at least once as this will certainly settle it into its last placement.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, position the tap in the installing opening in the bath/basin making sure that the washing machines are in area between the tap and the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall between the bath and also the tiling, leading to issues with wetness as well as possible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture relatively early if you do not take into account this activity before securing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water-proof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We had been shown that write-up on A Step-by-Step Guide to Installing a Bathtub from someone on our other web property. Those who enjoyed our page please be sure to share it. I treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Excellence awaits, dial!

    Report this page